| 논문명 |
나선철근 또는 U철근으로 횡보강된 SD400 D10 철근 겹침이음 실험 / Lap Splice Test of SD400 D10 Reinforcing Bars Confined with Spiral or U-Bar |
| 저자명 |
김진규(Jin-Gyu Kim) ; 천성철(Sung-Chul Chun) ; 김인호(In-Ho Kim) |
| 수록사항 |
한국콘크리트학회논문집, Vol.33 No.4 (2021-08) |
| 주제어 |
나선철근; U철근; 겹침이음; 설계식 ; spiral; U-bar; lap splice; design equation |
| 요약1 |
신구 슬래브의 접합을 위해서는 슬래브 철근의 이음이 필요하다. 철근을 겹침이음하기 위해서는 기존 슬래브 끝단의 콘크리트 파쇄가 불가피하다. 콘크리트 파쇄는 기존구조물의 손상을 야기하고 공사비 또한 매우 높다. 신구 슬래브 접합은 주로 응력이 낮은 위치로 설계하므로 SD400 D10 철근이 사용된다. 이 연구에서는 나선철근 또는 U철근으로 횡보강한 SD400 D10 철근의 이음실험을 수행하였다. 실험변수는 콘크리트 압축강도, 겹침이음 길이, 주철근의 간격, 철근의 위치 그리고 이음구간의 횡보강 형태로 설정하여 총 32개 실험을 수행하였다. 대부분의 실험체에서 예상강도보다 높은 강도를 발현하였다. 나선철근 또는 U철근으로 횡보강된 SD400 D10 철근은 10의 짧은 이음길이에서도 설계 항복강도 400 MPa를 발현하였다. 단면해석을 통하여 이음철근에 발현된 응력을 계산하고, 이 연구와 유사한 조건을 갖는 ACI 408 위원회 DB의 2개 자료를 포함하여 총 26개 실험결과를 4가지 제안식과 비교하였다. ACI 408 위원회 식이 [실험값]/[예측값] 비가 1.12로 1.0에 가장 가깝고, 변동계수가 12 %로 가장 낮아 신뢰성이 높았다. 다른 식보다 많은 설계 변수를 고려하는 ACI 408 위원회 식은 철근 지름의 영향도 고려하여 이 연구의 대상인 SD400 D10 철근의 이음강도를 비교적 정확히 평가하였다. ACI 408 위원회 식에 5 % 분위수 안전율을 적용하여 나선철근 또는 U철근으로 횡보강된 SD400 D10 철근의 이음길이 설계식을 제안하였다. |
| 요약2 |
Splices of reinforcing bars are needed to connect old and new concrete slabs. For lapping bars, breaking concrete in the old slab cannot be avoided, and this may cause deterioration in the old slab and increase repair costs. Connections are designed to be located in low stress regions and, SD400 D10 bars are often used. In this study, lap splice tests on SD400 D10 confined by spiral or U-bar were conducted. Test variables included concrete strength, lap length, spacing of splices, location of splice, existence of confining bars, and types of confining bars and a total of 34 specimens were tested. Most specimens showed higher bar stresses than expected. Splices of SD400 D10 confined by spiral or U-bar with only 10 db lap length developed a design yield strength of 400 MPa. Developed bar stresses were calculated through sectional analyses. Twenty-six stresses, including two specimens from the ACI 408 database, which had similar conditions to this study, were compared with four equations. The comparison shows that the ACI 408 equation can predict the bar stresses of confined SD400 D10 splice because, among the four equations, an average of test-to- prediction ratios by the ACI 408 equation is 1.12 and is the closest to 1.0, and the COV of the ratios is 12 % and is the lowest. More variables are included in the ACI 408 equation than the others and the ACI 408 equation can accurately predict the bar stresses of confined SD400 D10 splice. A design equation of splice length of SD400 D10 confined by spiral or U-bar is proposed from the ACI 408 equation incorporating a 5 % fractile coefficient. |